opet Lubricants

opet Lubricants Industrial and Other Lubricants Industrial Oils

DURA T 46

DURA T 46

Dura T Series, is a high performance hydraulic system oil which is suitable to use in wide temperature range. It can be used in all types of construction equipment and hydraulic system even under high pressure due to its special additive package in its content. It provides superior protection in hydraulic systems under extreme operating conditions.

Product Size

Technical Data Sheet Safety Data Sheet Technical Support

related products

Technical support

Engine Oils
Vehicle should be in 'stop' position and on a flat surface. The engine oil must be drained when hot. Ensure that the old oil in the engine crankcase fully discharged, whether used oil in engine pan is empty and whether pan bung is mounted properly.
In many respects, synthetic oils have superior properties than mineral oils. Long life is one of them. Compared to mineral oils, synthetic oils as a general principle it can be said to have the better extended oil drain intervals. However, the oil change intervals are determined by the vehicle manufacturers (OEMs) after a series of tests. Compliance with these oil change intervals is the best in terms of equipment health.
To understand for certain whether motor oil has perished, the oil should be analyzed physically and chemically under laboratory conditions.
Gear Oils
It is the API classification used for gear oils. Oil that contains additives to balance excessive pressure and pulsed load for hypoid gear type differentials running under heavy conditions and that fulfills MIL-L-2105 specifications. In GL-5, there are more overpressure additives and it is generally used under heavy work conditions. Unless otherwise specified, GL-5 should not be used in places where GL-4 is recommended. Because the sulphide in overpressure additive which is present excessively in GL-5 corrodes yellow metals.
The Association of Automotive Engineers (SAE) classifies automotive gear oils according to their kinematic viscosity values ​​at 100 °C and their pumpability at low temperatures. For example, the SAE 80W-90 in an automotive gear oil '90' describes the kinematic viscosity of this gear oil at 100 °C. As this number increases oil thickens, if the number decreases oil thins. The kinematic viscosity of '90' gear oil at 100 °C is between 13.50 and 18.50 cST while the kinematic viscosity of '140' gear oil at 100 °C must be between 24.00 and 32.50 cST. The number to the left of W (Winter) determines the performance of gear oil at low temperatures. Pumping temperature of '80W' gear oil is -26 °C while pumping temperature of '75W' gear oil is -40 °C.
Synthetic based oils are oils produced with chemical methods. They are produced to lubricate in applications where traditionally obtained mineral oils cannot be sufficient. Synthetic-based oils provide superior protection at higher temperatures than minerals, easier flow and pumpability at low temperatures , more stable film strength under extreme pressure and longer drain interval in difficult operating conditions.
Engine Oils
0W, expresses the viscosity grade of the engine oil. 'W' comes from the word 'winter'. '0' shows the cold working conditions of the engine oil. The kinematic viscosity of a 0W engine oil at 100 °C is at least 3.8 cST, which is pumpable even at -40 °C.
One of the duties of engine oil is to keep systems clean. A qualified engine oil incorporates soot particles in engine after separating them and prevent them from sticking on metal surfaces due to the detergent-dispersant additives in its content. It cleans soot particles adherent on metal surfaces with cleaning agent. Therefore, engine oil becomes dirty and its color turns black. If the motor oil is dirty, it is doing its job well.
As a general principle, mixing of oils with different properties and different brands is not appropriate. However, the decrease in oil was a variety of reasons and if it is necessary to complete the same viscosity and quality class can be added with other brand oils. It is recommended that the oil is completely drained and replaced with new oil at the most convenient time after the addition with another brand of oil. Hydraulic brake fluid at the same quality level can be mixed with each other regardless of brand.
Grease
In terms of application of lubricating with oil where it is not possible to use grease especially in ball bearings.
With manual hand pump or air pump can be printed directly into the bearing. In systems with central automatic lubrication, the grease is filled into the central chamber, the pneumatic system greases the greasing points automatically with the specified intervals.
Greases may leak during storage and base oil also tends to oscillate. The oil leakage rate will increase over time and will vary depending on the storage temperature. The grease should ideally be stored in a cool, dry interior and the ambient temperature should not exceed 30 °C and should not be less than 0 °C. The grease must be protected from dust, dirt, moisture or rainwater, and from direct sunlight.
ALL QUESTIONS