opet Lubricants Industrial and Other Lubricants Industrial Oils DURA T 32 Dura T Series, is a high performance hydraulic system oil which is suitable to use in wide temperature range. It can be used in all types of construction equipment and hydraulic system even under high pressure due to its special additive package in its content. It provides superior protection in hydraulic systems under extreme operating conditions. Product Size 15KG 205L Technical Data Sheet Safety Data Sheet Technical Support
DURA T 15 DURA T 32 DURA T 46 DURA T 68 DURA T 100 DURA 32 DURA 46 DURA 68 OPTIMA 68 OPTIMA 100 OPTIMA 150 OPTIMA 220 OPTIMA 320 MARINE C 50/70 MARINE DX 40/40 MARINE DT 40/30 MARINE DT 30/30 MARINE D 40/20 MARINE D 40/15 MARINE D 40/12 MARINE D 30/15 MARINE D 30/12 MARINE S 30/6
Engine Oils What springs to mind when it comes to viscosity? Viscosity is the resistance of fluids against flowing. An oil film is formed between the two surfaces under pressure with viscosity and system parts are provided to work for long years without abrasion. What issues should be considered when changing engine oil? Vehicle should be in 'stop' position and on a flat surface. The engine oil must be drained when hot. Ensure that the old oil in the engine crankcase fully discharged, whether used oil in engine pan is empty and whether pan bung is mounted properly. How is it possible to tell if motor oil has perished? To understand for certain whether motor oil has perished, the oil should be analyzed physically and chemically under laboratory conditions. Gear Oils What is the difference between synthetic oil and mineral oil? Synthetic based oils are oils produced with chemical methods. They are produced to lubricate in applications where traditionally obtained mineral oils cannot be sufficient. Synthetic-based oils provide superior protection at higher temperatures than minerals, easier flow and pumpability at low temperatures , more stable film strength under extreme pressure and longer drain interval in difficult operating conditions. What is automotive gear lubricant SAE viscosity classification? The Association of Automotive Engineers (SAE) classifies automotive gear oils according to their kinematic viscosity values at 100 °C and their pumpability at low temperatures. For example, the SAE 80W-90 in an automotive gear oil '90' describes the kinematic viscosity of this gear oil at 100 °C. As this number increases oil thickens, if the number decreases oil thins. The kinematic viscosity of '90' gear oil at 100 °C is between 13.50 and 18.50 cST while the kinematic viscosity of '140' gear oil at 100 °C must be between 24.00 and 32.50 cST. The number to the left of W (Winter) determines the performance of gear oil at low temperatures. Pumping temperature of '80W' gear oil is -26 °C while pumping temperature of '75W' gear oil is -40 °C. What does GL - 5 on gear oil packages mean? It is the API classification used for gear oils. Oil that contains additives to balance excessive pressure and pulsed load for hypoid gear type differentials running under heavy conditions and that fulfills MIL-L-2105 specifications. In GL-5, there are more overpressure additives and it is generally used under heavy work conditions. Unless otherwise specified, GL-5 should not be used in places where GL-4 is recommended. Because the sulphide in overpressure additive which is present excessively in GL-5 corrodes yellow metals. Engine Oils In case of oil loss, is it possible to add oil to another brand? As a general principle, mixing of oils with different properties and different brands is not appropriate. However, the decrease in oil was a variety of reasons and if it is necessary to complete the same viscosity and quality class can be added with other brand oils. It is recommended that the oil is completely drained and replaced with new oil at the most convenient time after the addition with another brand of oil. Hydraulic brake fluid at the same quality level can be mixed with each other regardless of brand. What is oil performance and how can we observe it? The information on the oil packaging contains important clues about performance of the oil. There should be information about five issues on the packaging in general. These; brand, its contents (be mineral, synthetic or synthetic based), viscosity grade (such as 5W-30, 10W-40), international performances (such as API CK-4, ACEA C3), OEM performances (such as MB-Approval 228.51, Volvo VDS- 4, VW 504 00/507 00). What does it mean if oil used in an engine turns black? One of the duties of engine oil is to keep systems clean. A qualified engine oil incorporates soot particles in engine after separating them and prevent them from sticking on metal surfaces due to the detergent-dispersant additives in its content. It cleans soot particles adherent on metal surfaces with cleaning agent. Therefore, engine oil becomes dirty and its color turns black. If the motor oil is dirty, it is doing its job well. Grease What are the conditions to keep grease? Greases may leak during storage and base oil also tends to oscillate. The oil leakage rate will increase over time and will vary depending on the storage temperature. The grease should ideally be stored in a cool, dry interior and the ambient temperature should not exceed 30 °C and should not be less than 0 °C. The grease must be protected from dust, dirt, moisture or rainwater, and from direct sunlight. Where is grease used? In terms of application of lubricating with oil where it is not possible to use grease especially in ball bearings. What are the intended uses of grease? With manual hand pump or air pump can be printed directly into the bearing. In systems with central automatic lubrication, the grease is filled into the central chamber, the pneumatic system greases the greasing points automatically with the specified intervals. ALL QUESTIONS